Alley Bump - GNR Technologies

Features

Constructed from 100% recycled tires, GNR alley bumps are preformed to ensure a smooth, safe ride. The Alley Bump's flexible design conforms to the contour of virtually any road surface. The bumps are simple to install and can be easily removed for storage or relocation. They are pre-drilled for anchoring spikes or lag bolts. Designed to withstand extreme temperature variations, the bumps are resistant to moisture, oil, and ultraviolet light. They will not warp, crack, chip, or rot.

Molded highly reflective tape ensures that the alley bumps are visible even on a dark night. Cat's eye reflectors further enhance visibility to alert drivers well in advance. The bumps have a channeled bottom to facilitate drainage as well as to cover cabling or piping.

The Alley Bump is available in 4' and 6' lengths, including end caps to protect the bump ends as well as vehicles. GNR rubber alley bumps are covered by a 3 year warranty.

Alley bumps are:

Made of 100% recycled rubber
Long lasting and cost efficient
Reduces speed to 1-5 mph
High visibility at night
Simple installation
Product can be installed in sections to create varying lengths
Will not warp, crack, chip or rot
Can be installed on any road surface
Resistant to ultraviolet light, moisture, oil, and extreme temperatures
Temporary or permanent installation
Channeled bottom for cabling and piping
Lowers insurance premiums for lot owners
Maintenance free
3 year warranty

Installation Locations:

Alleyways

Side streets

Narrow residential streets with hidden entrances

Dimensions

Alley Bump Dimensions:
(L) 4' x (W) 12" x (H) 3" - 51 lb.
(L) 6' x (W) 12" x (H) 3" - 76 lb.

Alley Bump End Cap Dimensions:

(L) 6" X (W) 12" X (H) 3" - 8 lb.

Technical Specs

Product name:

Rubber Speed Bumps - 3" thickness

Models:

6', 4' lengths

Product Description :

1. Material: compression molded composite: 100% recycled rubber and polyurethane prepolymer

2. Physical properties of the rubber composite: a. Density 0.6 oz/cu in (ASTM C642) b. Durometer Hardness 70A ± 7 (ASTM D2240) c. Tensile Strength 300 psi (ASTM D412) d. Compression deformation 7% at 70psi, 68°F (ASTM D575) e. Brittleness at Low temperature: -40°F (ASTM D746) f. Freeze and thaw when exposed to deicing chemicals no loss after 50 cycles (ASTM C672) g. Coefficient of thermal expansion: 8 x10-5 in/in/°F (ASTM C531) h. Weathering 70 hours at 158°F (ASTM D573) - hardness retained 100% (± 5%) - compressive strength 100% (± 5%) - tensile strength 100% (± 5%) - elongation retained 100% (± 5%)

3. Available models: 6', 4' lengths

4. Finishing: Black recycled rubber composite with yellow, durable and reflective, in-molded pavement marking tape

Components:

a) 100% recycled rubber from car and truck tires (NR, SBR)
b) polyurethane prepolymer
c) cat's eyes reflectors
d) yellow, durable and reflective in-molded pavement marking tape
e) molded in steel washers

Installation Guide

Components

Alley bumps
1/2" rebar spikes for asphalt or lag bolts with metal shields for concrete - available at GNR

What You Need

Gloves, safety glasses
Traffic cones, drums or barricades for securing the site
Mallet
Heavy duty electric drill
1/2" masonry bit and, if installed with lag bolts: a masonry bit required for the metal shields - consult bit size on side of shield
A drive socket and power tool for installation of the lag bolts

The flexible design of the Alley Bump allows the product to conform to the contour of uneven road surfaces and can be installed on both asphalt and concrete.

Installations Instructions for Asphalt: Installation of Alley Bumps with spikes

Step 1.

Drill 1/2" diameter holes in the asphalt through the product's holes.

Step 2.

Drive 1/2" rebar spike (14" long) through the holes in the product.

Installations Instructions for Concrete: Installation of Alley Bumps with lag bolts and metal shields

Step 1.

Use 1/2" or 5/8 lag bolts (5 1/2" long).

Step 2.

Drill 1/2" diameter pilot holes through the product's installation holes.

Step 3.

Remove the product; re-drill the holes for the diameter and depth required by the metal shields.

Step 4.

Install the metal shields, re-position the product and bolt with lag bolts.

Maintenance

Alley Bumps require minimal maintenance. Periodically inspect the bolts and tighten if necessary.

Some images of installation locations of the Alley Bump: