Cycle Lane Delineator - GNR Technologies

Cycle Lane Features

Manufactured from high-impact recycled rubber, the Cycle Lane solution is highly visible, durable, and easy-to-install. Unlike other delineation devices, the bike lane was designed for ultimate safety and protection of road cyclists.

This solution helps facilitate faster and safer commuting for all. By creating a physical barrier for bike lane traffic, both drivers and cyclists no longer have to worry about colliding with one another while in transit.

Ideal for municipal roadways and HOA's, bicycle paths can now be protected with confidence and ease.

Highly reflective striping is available in white.

Cycle Lane Delineators are:

Made from 100% recycled rubber
Long lasting and cost-efficient
Ideal for municipal roadways and HOA's
Highly visible at night
Quick and simple-to-install (does not require heavy machinery)
Suitable for permanent or temporary installation
Will not crack, chip, rot, or fade

Installation locations:

Municipal roadways
HOA's / private communities
University campuses

Cycle Lane Delineator Dimensions

Cycle Lane Dimensions:

(L) 29.5" (W) 4.75" x (H) 4" - 10 lbs

Technical Specs

Product Name:

Bike lane delineator

Models:

(L) 29.5" x (W) 4.75" x (H) 4"

Material :

Material: compression molded recycled rubber
Physical properties of the product:
     a) Density                                         0.6 oz/cu in                    (ASTM C642)
     b) Shore Hardness                             65A +/- 7                         (ASTM D2240)
     c) Minimum Tensile Strength               500 psi                             (ASTM D412)
     d) Coefficient of thermal expansion     8 x 10^-5 in/in/^oF     (ASTM C531)
Nominal dimensions:
     - width     4.75" (120 mm)
     - length   29.5" (750 mm)
     - height   4" (100 mm)
Finishing: black with reflective white tape

Components:

1. Recycled rubber
2. Durable and reflective white striping / marking tape

Installation Guide

Components

Cycle Lane Delineators available at GNR Technologies

Fasteners (available at GNR Technologies):

Zinc plated steel bolts (3/8" diameter x 4" long)
Plastic shields (9/16" diameter x 3" long)
Zinc plated steel washers (supplied with the product)

What You Need

Chalk line
Measuring tape
Heavy duty hammer drill and 9/16" (14 mm) carbide tip drill bit
Ratchet or power tool to screw down the installation bolts
Wrench with extension drive for bolt installation
Hammer fo installation of the plastic shields
Broom for cleaning installation surface
Portable blower or vacuum cleaner for cleaning installation holes from dust and other debris
Gloves, safety goggles
Traffic cones, barricades or other means to secure the workplace

Crew

2 -4 installers

Installations Instructions:

Step 1.

Determine where the Cycle Lane should be positioned and sweep the installation surface to ensure it is clean of debris / dust. Using the chalk line, mark the location for the bike lane delineator parallel to the curb.

Step 2.

Position the units following the chalk line. The units must be well aligned before moving on to Step 3.

Note: Make sure the sloped side of the product is facing the bike lane and the steep side of the product is facing vehicle traffic.

Step 3.

Drill 9/16" (14 mm) diameter holes into the surface, through the existing holes of the product using a hammer drill and carbide drill bit. The holes should be 3.5"-4" (90-100 mm) deep in order to accommodate the plastic shields that are 3" long.

Step 4.

Remove the product and clean the just drilled holes to ensure they are free from dust and debris (a portable blower is used for this purpose).

Once the holes are clean, insert the plastic shields.

Step 5.

Re-position the product over the holes made in the installation surface.

Step 6.

Insert the bolts and steel washers into the product's installation holes and tighten. Do not over-tighten the bolts.

Maintenance

Periodically inspect the bolts and tighten if necessary.

Some images of installation locations of Bike Lane Delineators:

Coming Soon!