 |
|
 |
|
 |
|
 |
|
 |
|
|
|
|
|
Features
Molded highly reflective tape ensures that the speed bumps are visible even on a dark night. Optional cat's eye reflectors further enhance visibility to alert drivers well in advance. The bumps have a channeled bottom to facilitate drainage as well as to cover cabling or piping.
Easy Rider® speed bumps are the ideal maintenance-free parking lot solution. In addition to enhancing parking lot safety, the bumps can lower insurance premiums for lot owners.
The Easy Rider® is available in 4' and 6' lengths including end caps to protect the speed bump ends and vehicles. GNR rubber speed bumps are covered by a 3 year warranty.
View our installation video for the Easy Rider® Speed Bump
Easy Rider® Speed Bumps are:
- Made of 100% recycled rubber
- Long lasting and cost efficient
- Reduces speed to 2-5 mph
- High visibility at night
- Simple installation
- Product can be installed in sections to create varying lengths
- Will not warp, crack, chip or rot
- Can be installed on any road surface
- Resistant to ultraviolet light, moisture, oil, and extreme temperatures
- Temporary or permanent installation - Relocatable when resurfacing / maintaining road surfaces; products can be stored and re-used
- Channeled bottom for cabling and piping
- Lowers insurance premiums for lot owners
- Maintenance free
- 3 year warranty
Applications:
Used for the following situations:
- Safety of pedestrian and vehicle traffic requires improvement
- To further support and reinforce stop signs in parking lots
- High risk of accidents on residential streets and in parking lots need to be reduced
- Permanent or temporary lowering speed of motor vehicles is required
- Only temporary installation is allowed or required
- Installation on surfaces where only flexible rubber speed bumps may fully conform to the curvature of the road
For more information on the Easy Rider® Speed Bump, read these newsletter issues:
- The GNR Reporter: February 2009
- The GNR Reporter: July 2008
- The GNR Reporter: May 2008
|
Available Online at:
www.SafestParkingProducts.com
|
|
Easy Rider® speed bumps
have been used in the following locations:
- Loyola Medical University
- US Army Corps of Engineers
- Luxor Hotel and Casino
- Best Western
- Carollsburg Condominium
- Greendale Mall
- Ryder Truck Rentals
- Lowes
- Whitlow Chevrolet
- Bethel Christian Center
- American Greetings Corp.
- Dairy Queen
- United Postal Service
- Wal Mart
- Dunkin Donuts
|
Installation Locations:
Shopping centers
School zones
Hotel entrances
Gas stations
Neighborhood intersections
Stop sign reinforcement
Parking lot gate entrances
Parking lots and garages
Gated communities
|
|
| |
|
|
| Dimensions |
| |
|
|
 |
|
Easy Rider® Speed Bump
Dimensions:
(L) 4' x (W) 12" x (H) 2 1⁄4" - 32 lb.
(L) 6' x (W) 12" x (H) 2 1⁄4" - 51 lb.
Easy Rider® End Cap
Dimensions:
(L) 9" X (W) 12" X (H) 2 1⁄4" - 5.5 lb. |
| |
|
|
| |
| |
| Technical Specs |
| |
| |
|
Product Name:
Rubber Speed Bumps 2 1/4" thick
|
|
|
Models:
6', 4' long
|
|
|
Product description:
1. Material: compression molded composite: 100% recycled rubber and polyurethane prepolymer
2. Physical properties of the rubber composite:
a. Density 0.6 oz/cu in (ASTM C642)
b. Durometer Hardness 70A ± 7 (ASTM D2240)
c. Tensile Strength 300 psi (ASTM D412)
d. Compression deformation 7% at 70psi, 68°F (ASTM D575)
e. Brittleness at Low temperature: -40°F (ASTM D746)
f. Freeze and thaw when exposed to de-icing chemicals no loss after 50 cycles (ASTM C672)
g. Coefficient of thermal expansion: 8 x10-5 in/in/°F (ASTM C531)
h. Weathering 70 hours at 158°F (ASTM D573)
- hardness retained 100% (± 5%)
- compressive strength 100% (± 5%)
- tensile strength 100% (± 5%)
- elongation retained 100% (± 5%)
3. Available models: 6', 4' long
4. Finishing: Black recycled rubber composite with yellow, durable and reflective, in-molded pavement marking tape
|
|
|
|
|
Components:
a)100% recycled rubber from car and truck tires (NR, SBR)
b)polyurethane prepolymer
c)cat's eyes reflectors
d) yellow, durable and reflective in-molded pavement marking tape
|
| |
| |
| Installation Guide |
| |
|
Components
Easy Rider® speed bumps
1/2" (diameter), 14" (length) rebar spikes for asphalt or lag bolts with metal shields for concrete - available at GNR
|
| |
| What You Need |
|
|
- Gloves, safety glasses
- Traffic cones, drums or barricades for securing the site
- Mallet
- Heavy duty electric drill
- 1/2" masonry bit and, if installed with lag bolts: a masonry bit required for the metal shields - consult bit size on side of shield
- A drive socket and power tool for installation of the lag bolts
The flexible design of the Easy Rider® Speed Bump allows the product to conform to the contour of uneven road surfaces and can be installed on both asphalt and concrete.
|
|
Installations Instructions for Asphalt: Installation of Easy Rider® Speed Bumps with spikes
|
|
|
Step 1.
Drill 1/2" diameter holes (3 - 4" in depth) in the asphalt through the product's holes.
|
|
|
|
Step 2.
Drive 1/2" rebar spike (14" long) through the holes in the product.
|
|
|
|
Installation Instructions for Concrete: Installation of Easy Rider® Speed Bumps with lag bolts and metal shields
|
| |
|
Step 1.
Use 1/2" or 5/8 lag bolts (5 1/2" long).
|
|
|
|
|
|
| Step 2.
Drill 1/2" diameter pilot holes (3 - 4" in depth) through the product's installation holes.
|
|
|
|
|
Step 3.
Remove the product; re-drill the holes for the diameter and depth required by the metal shields.
|
|
|
|
Step 4.
Install the metal shields, re-position the product and bolt with lag bolts.
|
|
|
Maintenance
|
|
|
| Speed bumps require minimal maintenance. Periodically inspect the bolts and tighten if necessary. |
|
|
Installation Instructions for Concrete or Asphalt: Installation of Easy Rider® Speed Bumps with PL Premium Adhesive
|
Components
Easy Rider® speed bumps
PL Premium Adhesive - available at GNR
|
| |
| What You Need |
|
|
- Gloves, safety glasses
- Traffic cones, drums or barricades for securing the site
- Street broom for cleaning the installation area
- Toluene
- Sanding tool (i.e. belt sander)
|
Step 1.
Clean the installation surface (concrete) from dust, water, or grease. The concrete surface must be completely dry.
|
|
Step 2.
Wash the bottom of the rubber speed bump with toluene until no slippery surface can be detected. Sand down the surface of the rubber in order to remove any residue from the mold release or other contaminants.
|
|
Step 3.
| Apply six (6) beads about 3/8" wide of the PL Premium adhesive on the cleaned bottom surface of the speed bump (two full 300 ml tubes of PL Premium should be used per 6' speed bump). |
 |
|
|
Step 4.
Position the speed bump on the designated, clean concrete surface.
|
|
Step 5.
Step and walk on the top of the speed bump to press it down and esnure the speed bump adheres to the concrete surface.
|
|
Step 6.
Leave the speed bump undisturbed for 12 – 24 hrs.*
|
Notes:
- Follow the PL Premium recommendation for minimum of 5°C (41°F) temperature of the installation surface.
- For installation of the speed bump end cap, use about 1/3 of the 300 ml tube of PL Premium and follow the same installation procedure as for the speed bump.
*It is necessary to leave the speed bump undisturbed for at least 12 hours. Closing off the area may be required.
|
|
|
|
